Altronix EFLOW104NK8QP | Networkable Dual Output Power Supply/Charger, 8 Fuse protected Auxiliary Class 2 Power-limited Outputs

Altronix EFLOW104NK8QP | Networkable Dual Output Power Supply/Charger, 8 Fuse protected Auxiliary Class 2 Power-limited Outputs

Altronix eFlow104NK8QP sub-assembly kit converts a 120VAC 60Hz input into eight (8) fuse protected outputs. Outputs are individually selectable, providing 12VDC or 5VDC up to 6A and/or 24VDC up to 10A (240W total power) for access control panels, door locks, and ancillary devices. Unit includes an unswitched aux. output. It also offers a suite of features that includes fire alarm disconnect, over voltage protection, and low power disconnect which prevents deep discharge of stand-by batteries. Networkable power distribution module facilitates monitoring, reporting, and control of the supervised DC power supply/charger over the network. It reports diagnostics via Email and Windows Dashboard Alert notifications, greatly reducing system downtime and eliminating unnecessary service calls.

• eFlow104NB Power Supply/Charger
• Input
• Voltage: 120VAC, 60Hz, 4.5A max.
• Input Fuse: 6.3A / 250V.
• Outputs
• Voltage: 24VDC @ 10A.
• Auxiliary: 1A (unswitched).
• Protection: Overvoltage protection. Filtered and regulated.
• Battery Backup (not included)
• Type: Sealed lead acid or gel type.
• Fuse Rating: 10A @ 32VDC.
• Failover: Upon AC loss, instantaneous.
• Fire Alarm Disconnect
• Supervised: Latching or non-latching.
• EOL: 10K Resistor.
• Supervision
• AC Failure: Form "C" contacts.
• Battery: Form "C" contacts.
• Low DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge.
• Indicators LED
• AC Input: 120VAC is present.
• DC Output: Powered.
• Battery: Discharged or not connected.
• VR6 Voltage Regulator
• Input
• Voltage: 24VDC from eFlow104NB.
• Output
• Voltage: 12VDC.
• Current: 6A continuous.
• Other: Surge suppression.
• Indicators LED
• Input: 24VDC is present.
• Output: Powered.
• LINQ8PD Network Power Distribution Module
• Input
• Voltage: 24VDC from eFlow104NB and 12VDC or 5VDC from VR6.
• Input Fuse: 15A / 32V.
• Outputs
• Eight (8) fused protected outputs rated 3A.
• Power output(s) can be locally or remotely controlled.
• Surge suppresion.
• Output Fuses: 3A/32VDC.
• Status Monitoring
• Power Supply output voltage and load.
• Voltage and load of each output.
• FACP trigger and reset status.
• Unit temperature (Celsius).
• Power Supply AC and Battery status.
• Battery health.
• Indicators (LED)
• Bat Local: Charging current status.
• FACP: Triggered / Released.
• Input: Input signal.
• Out1 - Out8: Bi-colored LEDs indicate 12 or 24VDC.
• Reporting
• Windows Dashboard Alert messages.
• E-mail notifications.
• Event Log tracks history.
• Programming Features
• Power Supply(ies) voltage and load limits (High/Low).
• FACP trigger type (wet or dry-N.O./N.C.).
• Input Function (FACP reset/tamper).
• Output Reset Trigger (N.O./N.C.).
• Battery Monitor Configuration:
• - Battery condition (Low/Normal/Missing)
• Configurable Output Relay(s).
• Individual Output Configuration:
• - Voltage and Current Limits (High/Low)
• - FACP Trigger Setting (latching/non-latching/inactive)
• Fire Alarm Interface
• Supervised FACP disconnect (Latching or Non-Latching).
• FACP reset (N.C. or N.O.).
• Environmental
• Temperature
• Operating: 0° C to 49° C (32° F to 120° F).
• Storage: - 20° C to 70° C ( - 4° F to 158° F).
• Relative Humidity
• Relative Humidity 85% +/- 5%.
• BTU/Hr (approx.):
• 123 BTU/Hr.

• Wall mount enclosure for indoor use.
• 1.125" and 1.375" combination knockouts.
• Unit provides 12VDC or 5VDC up to 6A and/or 24VDC up to 10A (240W total power)
• Additional aux. Class 2 power-limited output rated @ 1A
• Short circuit and overvoltage protection
• Fire alarm disconnect
• Built-in charger for sealed lead acid or gel type batteries