Altronix MAXFIT7F8AP | Access Power Controller Kit BC750 Enclosure with eFlow104NB, ACM8, PD8UL

Altronix MAXFIT7F8AP | Access Power Controller Kit BC750 Enclosure with eFlow104NB, ACM8, PD8UL

Altronix MaxFit7F8AP Access Power Controller distributes and switches power to access control systems and accessories. It converts a 120VAC, 60Hz input into eight (8) distributed 24VDC fuse protected outputs and eight (8) independently controlled 24VDC fuse protected relay outputs. Fail-Safe/Fail-Secure power outputs may be converted to dry form "C" contacts. Relays are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Keypad, Push Button, REX PIR, etc. Unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) relay outputs.

• eFlow104NB Power Supply/Charger
• Input
• Voltage: 120VAC, 60Hz, 4.5A max.
• Input Fuse: 6.3A / 250V.
• Outputs
• Voltage: 24VDC @ 10A.
• Auxiliary: 1A (unswitched).
• Protection: Overvoltage protection. Filtered and regulated.
• Back-up Battery (not included)
• Type: Sealed lead acid or gel type.
• Fuse Rating: 10A/32VDC.
• Failover: Upon AC loss, instantaneous.
• Fire Alarm Disconnect
• Supervised: Latching or non-latching.
• EOL: 10K Resistor.
• Supervision
• AC Failure: Form "C" contacts.
• Battery: Form "C" contacts.
• Low DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units (depending on the power supply).
• Prevents deep battery discharge.
• Indicators (LED)
• AC Input: 120VAC is present.
• DC Output: Powered.
• Battery: Discharged or not connected.
• PD8UL Power Distribution Module
• Input
• Voltage: 24VDC from eFlow104NB.
• Outputs
• Voltage: 24VDC.
• Eight (8) fuse protected outputs.
• 3.5A per output max.
• Output Fuses: 3.5A/32VDC.
• Indicators (LED)
• Green LED: DC Output.
• ACM8 Access Power Controller
• Input
• Voltage: 24VDC from eFlow104NB.
• Main Fuse: 10A / 32V.
• Outputs
• Voltage: 24VDC.
• Eight (8) independently controlled fused outputs:
• a) Fail-Safe and/or Fail-Secure power outputs.
• Form "C" Relays rated 28VAC or VDC @ 2.5A.
• b) Auxiliary power outputs (unswitched).
• c) Any combination of the above.
• Output Fuses: 3.5A / 32VDC.
• Indicators (LED)
• Red LEDs: Outputs are triggered (relays energized).
• Green LED: FACP disconnect is triggered.
• Environmental
• Temperature
• Operating: 0° C to 50° C (32° F to 122° F).
• Storage: - 20° C to 70° C ( - 4° F to 158° F).
• Relative Humidity
• Relative Humidity 85% +/- 5%.
• BTU/Hr (approx.):
• 145 BTU/Hr.

• Wall mount enclosure for indoor use.
• Accommodates up to four (4) 12VDC/12AH Batteries.
• 24VDC @ 10A power supply/charger
• Eight (8) distributed 24VDC fuse protected outputs
• Eight (8) independently controlled 24VDC fuse protected relay outputs
• 16 AWG powder-coated steel enclosure simplifies board layout and wire management
• Enclosure accommodates up to four (4) 12VDC/12AH batteries