Muxlab 500124 LongReach II Active CCTV Receiver Balun

The MuxLab LongReach II Active CCTV Receiver Balun allows you to achieve a separation of up to 5000’ (1500 m) between a CCTV camera and a DVR. Using the cost-efficient CAT5e/6/7 cables, this balun can easily be integrated with an existing cabling system. Auto Gain Control (AGC) amplifies the received signal and delivers high-quality video over long distances. Furthermore, the balun features ground loop isolation and auto polarity correction that enhances the quality of the received video signals. When used in conjunction with other MuxLab baluns, the LongReach II Active CCTV Receiver Balun simplifies routing solutions by enabling video, power, and PTZ signals to be sent over a single CAT5e/6/7 cable. As a measure of safety, this device comes with built-in surge protection and features LED indicators for you to keep an eye on its operation.

Features

Receives Video / Power / PTZ Signals

Uses a Single CAT5e/6/7 Cable

Transmits Signals up to 5000' (1500 m)

Auto Gain Control (AGC)

Ground Loop Isolation

Auto Polarity Correction

Built-In Surge Protection

Cast Aluminum Enclosure

LED Diagnostics

Specs

Manufacturer   Muxlab

Condition New

Environment CCTV composite baseband video; NTSC, PAL, SECAM

Devices CCTV cameras, monitors, DVR, switchers, IP encoders, and other CCTV equip

Transmission Transparent to the user

Video

Bandwidth 20 Hz to 8 MHz

Input 1.5 Vpp maximum, 100?, balanced (RJ45)

Output 1.1 Vpp, ± 1 dB, 75?, unbalanced (BNC)

Insertion Loss -14 dB minimum for luma, -60 dB minimum for chroma 1

Return Loss Greater than 15 dB over the frequency range

Common Mode Rejection Greater than 40 dB @ 3.85 MHz

Auto Polarity Correction Automatically adjusts for any polarity

Ground Loop Isolation Up to +/-50 VDC

Maximum Distance via Cat5e/6 5000' (1500 m) 2

LED Diagnostics Power, Video Sync

AGC (Automatic Gain Control) Automatically adjusts for gain, sharpness and luminosity

Remote Power

Wiring Remote low voltage power supported via 2 twisted pairs.

A Class II power supply is recommended

Maximum [email protected] VAC 2 VA : 1500' (457 m)

4 VA : 745' (227 m)

10 VA: 300' (91 m)

20 VA: 150' (46 m) 3

Maximum Current Fuse supports 2.5A rms or DC. Fuse trips @ 5A 4

2-Wire PTZ Control

Wiring Remote 2-wire PTZ control supported via one (1) twisted pair

Maximum Distance Up to 4000' (1200 m) depending on the PTZ camera vendor

Maximum Input Voltage 48 V (AC RMS/DC)

Maximum Current Rating 2 A (AC RMS/DC). No fuse

Mechanical & Environmental

Cable - UTP 24 gauge or lower solid copper twisted pair wire

Impedance: 100 ohms at 1 MHz

Maximum capacitance: 20 pf/foot

Attenuation: 6.6 dB/1000 feet at 1 MHz

Cable - Coax Impedance: 75 ? at 1 MHz. (RG59/U)

Switch Select between Power-Thru (500024 / 500029) and Pass-Thru (500022) mode 3

Compatible Baluns 500000, 500000R, 500009, 500022, 500024, 500100/101

Power Supply 5 VDC /6 W / 100 mA maximum

Floating +/- 20%. 150 mA maximum

Interchangeable blades

Surge Protection Above 34 VAC RMS or +/- 48 VDC

Fuse Auto-resettable fuse on 5 VDC input and Power A (+) upon power cycling

Temperature Operating: 32 to 131° F (0 to 55° C)

Storage: -4 to 185° F (-20 to 85° C)

Humidity: up to 95%

Enclosure ABS fire retardant plastic

Regulatory Approvals FCC and CE

Dimensions 2.4 x 2.25 x 1" (6.1 x 5.7 x 2.54 cm)